LED灯丝筛选方法研究

doi:10.3969/j.issn.1000-1158.2019.04.05

摘要
图/表
参考文献(20)
相关文章 (15)

全文: PDF (1416 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要从商业途径获得的LED灯丝相互之间总光通量的偏差达到7%,电压偏差高达0.6%。若灯丝不经过筛选直接用来制作标准灯,将达不到预期的光强空间分布,且发光稳定性降低,有效寿命减小。实验分析了LED灯丝在低驱动电流与额定驱动电流下电压、光通量的相关性,提出了一种在低于灯丝额定驱动电流下对LED灯丝进行快速筛选的方法。实验表明:采用驱动电流5mA代替额定驱动电流10mA进行筛选,电压、光通量的最大偏差仅为0.09%和0.65%,能满足筛选需要。采用这种筛选方法及开发的专用软件使得筛选过程操作简单、结果判定准确可靠,且不会减小灯丝的有效寿命,为LED灯丝总光通量标准灯的研制奠定了良好的基础,还可推广应用到LED灯丝生产过程中的质量控制。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	姜琳
	刘慧
	闫劲云
	赵伟强
	苏颖

关键词 ：计量学, LED灯丝, 筛选方法, LED总光通量标准灯, 光强空间分布, 预热时间

Abstract：For a group of commercially obtained LED filaments without screening, the difference of total luminous flux is 7% and the difference of voltage is 0.6% . If the filament is directly used to make standard lamps without screening, it will not achieve the expected luminous intensity spatial distribution, the lamp stability and rated life will be reduced also. A screening method for LED filament has been prosed based on a series experiment, the voltage and luminous flux correlation between low driven current and rated driven current is analyzed. It shows that if 5 mA is used to instead of the rated driven current 10 mA for screening, the maximum deviations of voltage and luminous flux are 0.09% and 0.65%, respectively, which can meet the screening needs. The developed screening method and related software make the screening process fast to operate, accurate and reliable to determine the results, and does not reduce the rated life of the filament. This has laid a good foundation for the development of total luminous flux standard lamp using LED filament, that can also be applied to quality control in the production process of LED filament.

Key words： metrology LED filament screening method LED total luminous flux standard lamp spatial distribution of luminous intensity warm up time

收稿日期: 2018-10-17 发布日期: 2019-06-10

PACS:

TB96

基金资助:国家自然科学基金 (61505191);国家市场监督管理总局质量技术监督能力提升专项(ANL1805)

通讯作者: 刘慧(1969-),女,陕西西安人,中国计量科学研究院副研究员,主要研究方向为光辐射测量。 Email: liuhui@nim.ac.cn E-mail: liuhui@nim.ac.cn

作者简介: 姜琳(1995-),女,内蒙古兴安盟人,中国计量科学研究院在读研究生,主要研究方向为光辐射测量。 Email: 13260251519@163.com

引用本文:

姜琳,刘慧,闫劲云,赵伟强,苏颖. LED灯丝筛选方法研究[J]. 计量学报, 2019, 40(4): 569-575.
JIANG Lin,LIU Hui,YAN Jin-yun,ZHAO Wei-qiang,SU Ying. Research on Screening Methods of LED Filament. Acta Metrologica Sinica, 2019, 40(4): 569-575.

链接本文:

http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2019.04.05 或 http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2019/V40/I4/569

［1］Ohno Y, Nara K. Solid State Lighting Annex 2013, Interlaboratory Comparison Final Report, International Energy Agency ［EB］. http://ssl. iea-4e. org, 2018-10-30.
［2］Metzdorf J, Sperling A, Winter S, et al. A new FEL-type quartz-halogen lamp as an improved standard of spectral irradiance ［J］. Metrologia, 1998, 35(4): 423-426.
［3］Ohno Y, Jackson J K. Characterization of modified FEL quartz-halogen lamps for photometric standards ［J］. Metrologia, 1995, 32(6): 693-696.
［4］Sperling A, Bentlage V. A stabilized transfer-standard system for spectral irradiance ［J］. Metrologia, 1998, 35(4): 437-440.
［5］Katona T M, Pattison P M, Paolini S. Status of Solid State Lighting Product Development and Future Trends for General Illumination ［J］. Annual Review of Chemical and Biomolecular Engineering, 2016, 7: 263-281.
［6］Willstrop R V. Review of Handbook of Applied Photometry ［J］. Measurement Science & Technology, 1997,8(10):1191.
［7］Sametoglu F. Influence of the spectral power distribution of a LED on the illuminance responsivity of a photometer ［J］. Optics & Lasers in Engineering, 2008, 46(9): 643-647.
［8］Zhao W Q, Liu H, Liu J. Estimation of the sampling interval error for LED measurement with a goniophotometer ［C］// International Conference on Optics in Precision Engineering & Nanotechnology. International Society for Optics and Photonics. China, Beijing, 2013.
［9］Zwinkels J C. CCPR Activities Related to LED-based Calibration Standards ［C］// CIE. Melbourne, Australia, 2016.
［10］Dnsberg T, Pulli T, Poikonen T, et al. New source and detector technology for the realization of photometric units ［J］. Metrologia, 2014, 51(6): S276-S281.
［11］刘慧, 刘建, 赵伟强, 等. 一种基于LED灯丝灯的标准灯的研制［J］. 照明工程学报, 2017, 28(2): 13-16.
Liu H, Liu J, Zhao W Q, et al. The Development of LED Filament Standard Lamp ［J］. China Illuminating Engineering Journal, 2017, 28(2): 13-16.
［12］JJG247-2008 总光通量标准白炽灯检定规程［S］.

［13］JJG246-2005 发光强度标准灯检定规程［S］.

［14］Ohno Y. Improved Photometric Standards and Calibration Procedures at NIST ［J］. Journal of Research of the National Institute of Standards & Technology, 1997, 102(3): 323-331.
［15］杨光. LED灯丝灯配光的探讨［J］. 光源与照明, 2017,(02): 39-41.
Yang G. Discussion on light distribution of LED filament lamp ［J］. Lamps and Lighting, 2017,(02): 39-41.
［16］吴朝晖, 程浩, 章军, 等. 大功率LED封装基板技术与发展现状［J］. 半导体光电, 2016, 37(1): 1-6.
Wu C H, Cheng H, Zhang J, et al. Technologies and Development Status of Heat Spreader for High-power LED Packaging ［J］. Semiconductor Optoelectronics, 2016, 37(1): 1-6.
［17］钱斐, 傅仁利, 张鹏飞, 等. 陶瓷基板及钎焊技术对LED散热性能的影响［J］. 电子元件与材料, 2014, 33(02): 47-51.
Qian F, Fu R L, Zhang P F, et al.Influence of ceramic substrate and soldering join technology on thermal dissipation performance of LED ［J］. Electronic Components & Materials, 2014, 33(02): 47-51.
［18］刘波, 郑伟, 李海洋, 等. LED热分析测试和热管理技术研究进展［J］. 照明工程学报, 2018, 29(02): 28-34.
Liu B, Zheng W, Li H Y, et al. Research Progress on LED Thermal Analytical Test and Thermal Management Technology ［J］. China Illuminating Engineering Journal, 2018, 29(02): 28-34.
［19］Park S, Kim Y W, Lee D H, et al. Preparation of a standard light-emitting diode (LED) for photometric measurements by functional seasoning ［J］. Metrologia, 2006, 43(3): 299-305.
［20］汪钢, 赵正之. LED灯丝灯泡的结温测量［C］// 2014中国长三角照明科技论坛暨上海市照明学会会员大会论文集. 上海, 2014.
Wang G, Zhao Z Z. Junction temperature measurement of LED filament lamp ［C］// 2014 China Yangtze River Delta lighting technology forum and Shanghai lighting society general meeting. Shanghai, China, 2014.