A New Method to Compare Two Shunt-TVC Combinations at Common Ground at Frequency up to 200 kHz
PAN Xian-lin1,ZHANG Jiang-tao1,SHI Zhao-min1,SONG Ying1,JIA Zheng-sen1,WANG Rong-yu2,DING Xiang3
1. National Institute of Metrology, Beijing 100029, China
2. Guizhou Institute of Metrology, Guiyang, Guizhou 550003, China
3. Beijing Institute of Metrology, Beijing 100029, China
Abstract：Compared with the traditional series connection method, a method based on binary reactance shunt for thermoelectric converter common ground comparison measurement is proposed, so that the AC current range extension can be achieved by series connection. The method was based on binary inductive current divider (BICD) to provide two currents and compare two shunt-TVC combinations directly at common ground.This method can reduce the influence of current leakage and tee connector in series connection. Based on the common ground measurement method, the measurement between two shunt-TVC combinations with 100 mA and 1 A current shunts was done respectively at frequencies up to 200 kHz. At the same time, the measurement of the traditional exchanging position method was carried out in the series mode. The experimental results showed that the measurement error caused by leakage current can be eliminated well based on BICD and exchanging position method, and the two different methods were consistent at 200 kHz, it were better than 3 μA/A. The consistency of AC conversion error of three different shunt-TVC combinations were better than 6 μA/A under the current of 10 mA~1 A.
潘仙林,张江涛,石照民,宋莹,贾正森,王嵘瑜,丁香. 基于二进制电抗分流器实现热电变换器共地测量[J]. 计量学报, 2020, 41(3): 317-321.
PAN Xian-lin,ZHANG Jiang-tao,SHI Zhao-min,SONG Ying,JIA Zheng-sen,WANG Rong-yu,DING Xiang. A New Method to Compare Two Shunt-TVC Combinations at Common Ground at Frequency up to 200 kHz. Acta Metrologica Sinica, 2020, 41(3): 317-321.
［1］Klonz M, Laiz H, Kessler E. Development of thin-film multijunction thermal converters at PTB/IPHT［J］. IEEE Trans Instrum Meas, 2001, 50(6): 1 490-1 498.
［2］Williams E S. Thermal current converters for accurate ac current measurements［J］. IEEE Trans Instrum Meas, 1976, 25(4): 519-523.
［3］Klonz M. AC-DC transfer difference of the PTB multijunction thermal converter in the frequency range from 10 Hz to 100 kHz［J］. IEEE Trans Instrum Meas, 1987, 36(3): 320-328.
［4］Scarioni L, Klonz M. Explanation for the AC-DC Voltage Transfer Differences in Thin-Film Multijunction Thermal Converters on Silicon Chips at High Frequencies［J］. IEEE Trans Instrum Meas, 2007, 56(2): 567-570.
［5］Klonz M, Laiz H. AC-DC current transfer step-up and step-down calibration and uncertainty calculation［J］. IEEE Trans Instrum Meas, 2002, 51(5): 1 027-1 033.
［6］Funck T, Klonz M. Improved ac-dc current transfer step-up with new current shunts and potential driven guarding［J］. IEEE Trans Instrum Meas, 2007, 56(2): 361-364.
［7］Kinard J R, Lipe T E, Childers C B. Extension of the NIST AC-DC difference calibration service for current to 100 kHz［J］. NIST J Res, 1997, 102(1): 75-83.
［8］Kinard J R, Lipe T E, Childers C B. AC-DC difference relationships for current shunt and thermal converter combinations［J］. IEEE Trans Instrum Meas, 1991, 40(2): 352-355.
［9］Filipski P S, Boecker M, Garcocz M. 20-A to 100-A AC-DC Coaxial Current Shunts for 100 kHz Frequency Range［J］. IEEE Trans Instrum Meas, 2008, 57(8): 1 637-1 641.
［10］Rydler K E. High precision automated measuring system for AC-DC current transter standards［J］. IEEE Trans Instrum Meas, 1993, 42(2): 608-611.
［11］Pan X L, Zhang J T. A Coaxial Time Constant Standard for the Determination of Phase Angle Errors of Current Shunts［J］. IEEE Trans Instrum Meas, 2013, 62(1): 199-204.
［12］Pan X L, Zhang J T, Shao H M, et al. Measurement of the phase angle errors of high current shunts at frequencies up to 100 kHz［J］. IEEE Trans Instrum Meas, 2013, 62(6): 1 652-1 657.
［13］Zhang J T, Pan X L, Lin J, et al. A new method for measuring the level dependence of ac shunts［J］. IEEE Trans Instrum Meas, 2010, 59(1): 140-144.
