高精度钾热管铝凝固点炉研制及性能测试

doi:10.3969/j.issn.1000-1158.2022.11.05

摘要
图/表
参考文献(18)
相关文章 (15)

全文: PDF (1121 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要热管作为等温炉衬可提高固定点炉温场均匀性。为提高铝凝固点复现水平,研制了1套高精度钾热管铝凝固点炉。介绍了钾热管和固定点炉的研制流程,并测试了钾热管固定点炉性能。测试结果表明:采用分段升温的方式,炉子升温曲线平缓,整个升温过程中没有明显过冲现象,可有效保护铝凝固点容器的使用寿命;钾热管铝凝固点炉垂直温场均匀性为6.6mK;利用该钾热管铝凝定点炉可以实现铝凝固点温坪的复现,温坪重复性为0.02mK。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	刘颖
	闫小克
	张静
	王宁
	张雯

关键词 ：计量学;钾热管;铝凝固点;固定点炉, 温场均匀性;温坪;ITS-90

Abstract：As isothermal furnace liners, heat pipes can be used to improve the temperature uniformity of the fixed point furnaces. In order to improve the reproducibility of the freezing point of aluminum, a potassium heat pipe fixed point furnace for aluminum freezing point was developed. The production processes of potassium heat pipe and fixed point furnace were introduced, and the performance of the potassium heat pipe furnace was tested. The results show that there was no obvious temperature overshoot during the heating process of furnace startup, which can effectively extend the service life of the aluminum fixed point cell. The vertical temperature uniformity was 6.6mK. The repeatability of aluminum freezing point realized by the furnace was 0.02mK.

Key words： metrology potassium heat pipe aluminum freezing point fixed point furnace temperature uniformity;plateau;ITS-90

收稿日期: 2021-04-16 发布日期: 2022-11-14

PACS:

TB942

基金资助:国家重点研发计划(2017YFF0205901)

通讯作者: 闫小克(1974-),男,河南内乡人,中国计量科学研究院研究员,主要从事热管技术及温度源的研究。Email:yanxk@nim.ac.cn E-mail: ly20198@163.com

作者简介: 刘颖(1989-),湖北荆州人,重庆市计量质量检测研究院高级工程师,主要从事热工计量测试技术的研究。Email:ly20198@163.com

引用本文:

刘颖,闫小克,张静,王宁,张雯. 高精度钾热管铝凝固点炉研制及性能测试[J]. 计量学报, 2022, 43(11): 1418-1423.
LIU Ying,YAN Xiao-ke,ZHANG Jing,WANG Ning,ZHANG Wen. Development and Performance Test of High Precision Potassium Heat Pipe Furnace for Aluminum Fixed Point. Acta Metrologica Sinica, 2022, 43(11): 1418-1423.

链接本文:

http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2022.11.05 或 http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2022/V43/I11/1418

［1］Rusby R L, Hudson R P, Durieux M, et al. Thermodynamic Basis of the ITS-90［J］. Metrologia, 1991, 28(1):9-18.
［2］瞿咏梅. 复现90温标定义固定点时杂质引起的偏差估算［J］. 计量学报, 2000, 21(4):279-285.
Qu Y M. Estimation of error due to impurities on fixed-point temperatures［J］. Acta Metrologica Sinica, 2000, 21(4):279-285.
［3］傅广生, 康志茹. 0.01～961.78℃分温区90国际温标的传播不确定度方程［J］. 计量学报, 2006, 27(3):241-245.
Fu G S, Kang Z R. Equations of propagation of uncertainty on ITS-90 in the sub-range from 0.01 to 961.78℃［J］. Acta Metrologica Sinica, 2006, 27(3):241-245.
［4］Zhao Q, Duan Y N. Review of Progress in the implementation of the ITS-90 at the NIM ［J］. Metrologia, 1996,33:369-374.
［5］Mangum B W, Strouse G F, Guthrie W F. CCT-K3:key comparison of realization of the ITS-90 over the range from 83. 8058K to 933. 473K［R］. CCT, 2002.
［6］Nubbemeyer H G, Fischer J. Reprot to the CCT on key comparison 4 comparison of local realization of aluminiun and silver freezing-point temperture［R］. CCT, 2007.
［7］曲伟, 王焕光, 段彦军. 高温及超高温热管的启动特性和传热极限［J］. 工程热物理学报, 2011, 32(8):1345-1348.
Qu W, Wang H G, Duan Y J. Startup characteristics and heat transfer limits of high and super high temperature heat pipes［J］. Journal of engineering thermophysics, 2011, 32(8):1345-1348.
［8］田智星, 刘逍, 王成龙, 等. 高温钾热管稳态运行传热特性研究［J］. 原子能科学技术, 2020, 54(10):1771-1778.
Tian Z X, Liu X, Wang C L, et al. Study on heat transfer performance of high temperature potassium heat pipe at steady state［J］. Atomic Energy Science and Technology, 2020, 54(10):1771-1778.
［9］贾先剑, 郭航, 郭青, 等. 加热温度对钠钾合金热管启动和传热性能影响［J］. 太阳能学报, 2019, 40(1):17-23.
Jia X J, Guo H, Guo Q, et al. Effect of heating temperature on start-up and heat transfer performance of Na-K alloy heat pipe［J］. Acta Energiae Solaris Sinica, 2019, 40(1):17-23.
［10］何沛,林林,闫小克,等. 三段控温固定点炉复现铝凝固点研究［J］. 计量学报, 2021, 42(3):321-326.
He P,Lin L,Yan X K,et al. Study on the Realization of Aluminum Freezing Point in the Three-zone Temperature Controlled Fixed Point Furnace［J］. Acta Metrologica Sinica, 2021, 42(3):321-326.
［11］童文雨, 张广明, 于莉莉, 等. N-甲基吡咯烷酮热管启动性能和等温性能实验研究［J］. 计量学报, 2020, 41(2):170-174.
Tong W Y, Zhang G M, Yu L L, et al. Experimental study on the start-up characteristic and isothermal performance of the N-methyl pyrrolidone heat pipe［J］. Acta Metrologica Sinica, 2020, 41(2):170-174.
［12］柴宝华, 杜开文, 卫光仁, 等. 钾热管稳态数值模拟分析［J］. 原子能科学技术, 2010,44(5):553-557.
Chai B H, Du K W, Wei G R, et al. Steady numerical analysis of potassium heat pipe［J］. Atomic Energy Science and Technology, 2010(5):553-557.
［13］王刚, 熊亚选, 吴玉庭, 等. 高温熔盐热管的启动和等温性能［J］. 化工学报, 2020, 71(11):259-266.
Wang G, Xiong Y X, Wu Y T, et al. Startup and isothermal performance of high-temperature molten salt heat pipe［J］. CIESC Journal, 2020, 71(11):259-266.
［14］张凯, 乐恺, 闫小克, 等. 重力铯热管等温性能研究［J］. 计量学报, 2020, 41(1):26-31.
Zhang K, Yue K, Yan X K, et al. Study on isothermal characteristics of gravity cesium heat pipe［J］. Acta Metrologica Sinica, 2020, 41(1):26-31.
［15］Jang J H. Startup characteristics of a potassium heat pipe from the frozen state［J］. Journal of Thermophysics and Heat Transfer, 1995, 9(1):117-122.
［16］郭航, 贾先剑, 郭青, 等. 不同加热功率条件下钠钾合金热管启动和传热性能［J］. 航空动力学报, 2019, 34(1):1-7.
Guo H, Jia X J, Guo Q, et al. Start-up and heat transfer performance of a sodium-potassium alloy heat pipe under different conditions of heating power［J］. Journal of Aerospace Power, 2019, 34(1):1-7.
［17］Yan X K, Duan Y N, Ma C F, et al. Construction of Sodium Heat-Pipe Furnaces and the Isothermal Characteristics of the Furnaces［J］. International Journal of Thermophysics, 2011, 32(1):494-504.
［18］闫小克, 张金涛, 马重芳, 等. 钠热管炉复现铝凝固点［J］. 计量学报, 2009, 30(4):317-320.
Yan X K, Zhang J T, Ma C F, et al. Realization of the aluminum freezing point using solium heat pipe furnace［J］. Acta Metrologica Sinica, 2009, 30(4):317-320.