多边法坐标测量系统中解算方式对测量精度的影响研究

doi:10.3969/j.issn.1000-1158.2021.05.03

摘要
图/表
参考文献(16)
相关文章 (15)

全文: PDF (1843 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为了研究多边法坐标测量系统中解算方式对测量精度的影响,建立了多边法坐标测量模型,分析了两种目标点坐标解算方式的差异,并针对典型的4台测站多边法坐标测量系统进行了两种解算方式的仿真测量实验。仿真结果表明:预先准确标定系统参数方式能有效提升测量精度,测量精度依次改善了69.5%、64.6%、46.3%。进行了坐标测量精度验证实验,实验结果表明:与同步解算方式相比较,预先准确标定系统参数取模后的3组实验平均测量误差由203.0μm降至23.8μm,且3组实验的测量误差与测量距离的平均相关系数由99.8%降至37.8%,验证了仿真实验结果。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	孙威
	缪东晶
	李建双
	姚燕
	钟文
	赫明钊
	李连福

关键词 ：计量学, 大尺寸测量, 多边法坐标, 解算方式, 测量精度

Abstract：In order to study the influence of the calculation method on the accuracy of the multilateral coordinate measurement system,the multilateral coordinate measurement model was established,and the differences between the two methods of coordinate calculation were analyzed.The simulation experiment of the two methods was carried out for the typical multilateral coordinate measurement system of four stations.The simulation results show that the pre-accurate calibration of system parameters can effectively improve the measurement accuracy,which is improved by 69.5%,64.6% and 46.3% respectively.An experiment was conducted to verify the accuracy of coordinate measurement.The experimental results show that,compared with the synchronous calculation method,the average measurement error of the three groups of experiments after the pre-accurate calibration of system parameters decrease from 203.0μm to 23.8μm,and the average correlation coefficient between the measurement error and the measurement distance of the three groups of experiments is reduced from 99.8% to 37.8%,which verify the simulation results.

Key words： metrology large scale measurement;multilateral coordinate;method of calculation;measurement accuracy

收稿日期: 2020-06-08 发布日期: 2021-05-24

PACS:

TB92

基金资助:国家重点研发计划(2017YFF0204802)

通讯作者: 缪东晶(1985-),福建周宁人,中国计量科学研究院副研究员,主要从事大尺寸计量技术与自动化测量技术研究。Email:miaodj@nim.ac.cn E-mail: miaodj@nim.ac.cn

作者简介: 孙威（1995-）,江苏徐州人,中国计量大学在读研究生,研究方向为大空间位姿测量。Email:sunwei.youxiang@qq.com

引用本文:

孙威,缪东晶,李建双,姚燕,钟文,赫明钊,李连福. 多边法坐标测量系统中解算方式对测量精度的影响研究[J]. 计量学报, 2021, 42(5): 558-563.
SUN Wei,MIAO Dong-jing,LI Jian-shuang,YAO Yan,ZHONG Wen,HE Ming-zhao,LI Lian-fu. Study on the Influence of the Calculation Method on the Accuracy of the Multilateral Coordinate Measurement System. Acta Metrologica Sinica, 2021, 42(5): 558-563.

链接本文:

http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2021.05.03 或 http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2021/V42/I5/558

［1］张俐, 华强. 飞机大部件位姿调整的关键测量特征点误差控制权值计算方法［J］. 计量学报, 2019, 40 (3): 397-402.
Zhang L, Hua Q. Calculation method for key measure-ment feature point error control weight of aircraft large part position adjustment ［J］. Acta Metrologica Sinica, 2019, 40 (3): 397-402.
［2］Schmitt R H, Peterek M, Morse E, et al. Advances in Large-Scale Metrology-Review and future trends ［J］. CIRP Annals-Manufacturing Technology, 2016, 65 (2): 643-665.
［3］叶声华, 邾继贵, 张滋黎, 等. 大空间坐标尺寸测量研究的现状与发展［J］. 计量学报, 2008, 29 (Z1): 1-6.
Ye S H, Zhu J G, Zhang Z L, et al. Status and dev-elopment of large-scale coordinate measurement research ［J］. Acta Metrologica Sinica, 2008, 29 (Z1): 1-6.
［4］陈晓怀, 姜瑞, 王汉斌, 等. CMM在产品检验中的不确定度分析与合格性判定［J］. 计量学报, 2017, 38 (1): 51-55.
Chen X H, Jiang R, Wang H B, et al. Uncertainty Analysis and Qualification Determination of CMM in Pro-duct Inspection ［J］. Acta Metrologica Sinica, 2017, 38 (1): 51-55.
［5］史建华, 刘盼. 大尺寸航空发动机叶片的高效型面检测方法［J］. 计量学报, 2018, 39 (5): 605-608.
Shi J H, Liu P. High-efficiency profile detection method for large-size aero-engine blades ［J］. Acta Metrologica Sinica, 2018, 39 (5): 605-608.
［6］张红英, 余晓芬, 王标, 等. 大空间坐标测量网络的现场实时标定方法［J］. 计量学报, 2018, 39 (1): 1-5.
Zhang H Y, Yu X F, Wang B, et al. On-site real-time calibration method for large space coordinate measurement network ［J］. Acta Metrologica Sinica, 2018, 39 (1): 1-5.
［7］Camboulives M, Lartigue C, Bourdet P, et al. Calibra-tion of a 3D working space by multilateration ［J］. Precision Engineering, 2016, 44: 163-170.
［8］Takatsuji T, Goto M, Kirita A, et al. The relationship between the measurement error and the arrangement of laser trackers in laser trilateration ［J］. Measurement Science and Technology, 2000, 11 (5): 477-483.
［9］林永兵, 李杏华, 张国雄. 基于多边法的三维坐标测量系统自标定最优方案［J］. 计量学报, 2003, 24 (3): 166-173.
Lin Y B, Li X H, Zhang G X, et al. Self-Calibration and its optimal method for 3D coordinate measuring System based on multi-lateral principle ［J］. Acta Metrologica Sinica, 2003, 24 (3): 166-173.
［10］范百兴, 李广云, 李佩臻, 等. 激光干涉测量三维点坐标的PDOP模型研究和应用［J］. 测绘通报, 2015, (11): 28-31.
Fan B X, Li G Y, Li P Z, et al. PDOP Model of Laser Interferometry 3D Trilateration Network ［J］. Bulletin of Surveying and Mapping, 2015, (11): 28-31.
［11］Miao D, Wang G, Li J, et al. An improved self-calibration algorithm for multilateration coordinates mea-suring system［C］//Eighth International Symposium on Advanced Optical Manufacturing and Testing Technology (AOMATT2016). Suzhou, China, 2016.
［12］Zhang F M, Zhang H D, Qu X H. A multilateral laser-tracking three-dimensional coordinate measuring system based on plane constraint ［J］. Measurement Science and Technology, 2020, 31 (1): 015205.
［13］任瑜, 刘芳芳, 傅云霞, 等.激光多边测量网布局优化研究［J］.激光与光电子学进展, 2019, 56 (1): 159-164.
Ren Y, Liu F F, Fu Y X, et al. Placement Optimi-zation of Laser Multilateration Network ［J］. Laser & Optoelectronics Progress, 2019, 56 (1): 159-164.
［14］Zhuang H, Li B, Roth Z S, et al. Self-calibration and mirror center offset elimination of a multi-beam laser tracking system ［J］. Robotics and Autonomous Systems, 1992, 9 (4): 255-269.
［15］郑继辉,缪东晶,李建双,等. 采用标准长度的激光多边法坐标测量系统自标定算法［J］. 计量学报, 2019, 40 (1): 64-70.
Zheng J H, Miao D J, Li J S, et al.Self-calibration algorithm for standard length laser multi-method coordi-nate measuring system ［J］. Acta Metrologica Sinica, 2019, 40 (1): 64-70.
［16］倪思方. 激光跟踪仪校准中的测量不确定度评估［J］. 工业计量, 2012, 22 (S1): 92-96.
Ni S F. Evaluation of measurement uncertainty in laser tracker calibration ［J］. Industrial Metrology, 2012, 22 (S1): 92-96.