长导轨直线度分段测量拼接方法研究

doi:10.3969/j.issn.1000-1158.2022.07.01

摘要
图/表
参考文献(18)
相关文章 (15)

全文: PDF (3304 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要激光干涉仪测量超长导轨直线度时,因导轨长度超出干涉仪直线度测量范围,需分段测量后拼接,测量数据易受噪声和激光漂移等因素影响,导致拼接可能引入较大误差。通过分析拼接过程中的影响因素,结合长导轨结构特性,提出了一种将拼接公共点分布在相邻两节子导轨上,利用相邻两节子导轨夹角的稳定特性来实现长导轨直线度拼接的方法。通过仿真与实验,对比了30m范围内的直接测量法与坐标变换拼接法的测量结果,2种方法的直线度结果相差＜10μm,表明所提出的方法能有效减小拼接误差。将此方法应用于72m导轨的直线度测量,并与电子水平仪测量方法比较,2种方法结果相差10μm,表明所提出的方法可实现高精度的直线度拼接。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	李婷
	缪东晶
	李连福
	李建双
	钟文

关键词 ：计量学, 超长导轨, 激光干涉仪, 拼接方法, 直线度, 分段测量, 坐标变换

Abstract：When using the interferometer to measure the straightness of the ultra-long rail, the stitching may introduce a large error due to the length of the rail exceeding the measurement range of the interferometer, since the straightness of the whole long guide rail needs to be divided into multiple sections and then each straightness is measured separately.By analyzing the influencing factors in the splicing process, and combined with the structural characteristics of long guide rails, a new straightness splicing method for long guide rails is proposed.This method uses common points distributed on two adjacent sub-guide rails for splicing, and uses the stable characteristic of the angle between two adjacent sub-guide rails to realize straightness splicing .Through simulation and experiment, the measurement results of the direct measurement method and the coordinate transformation splicing method in the range of 30m are compared, and the difference of straightness results between the two methods is less than 10μm, which shows that the proposed method can effectively reduce the stitching error.Finally, this method is applied to the straightness measurement of 72m rail, and compared with the electronic level measurement method, the difference of the two results methods is 10μm, which indicated that the proposed method can achieve high-precision straightness stitching.

Key words： metrology long guideway laser interferometer stitching method straightness segment measurement coordinate transformation

收稿日期: 2021-02-24 发布日期: 2022-07-18

PACS:

TB921

基金资助:国家重点研发计划(2017YFF020630)

通讯作者: 李建双(1966-),女,浙江余姚人,中国计量科学研究院副研究员,工程博士,主要从事大长度计量研究工作。Email:lijiansh@nim.ac.cn E-mail: miaodj@nim.ac.cn

作者简介: 李婷(1982-),女,湖南桂东人,湖南省计量检测研究院工程师,硕士,主要从事几何量计量。Email:519094571@qq.com

引用本文:

李婷,缪东晶,李连福,李建双,钟文. 长导轨直线度分段测量拼接方法研究[J]. 计量学报, 2022, 43(7): 837-843.
LI Ting,MIAO Dong-jing,LI Lian-fu,LI Jian-shuang,ZHONG Wen. Research on Stitching Method for Segment Straightness Measurement of the Long Guideway. Acta Metrologica Sinica, 2022, 43(7): 837-843.

链接本文:

http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2022.07.01 或 http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2022/V43/I7/837

［1］逯圣周. 重型机床大尺寸部件几何精度测量技术研究［D］. 哈尔滨: 哈尔滨工业大学, 2015.
［2］戈娟, 张伟, 贺凤宝. 导轨直线度对测量结果的影响［J］. 机床与液压, 2014, 42 (2): 97-99.
Ge J, Zhang W, He F B. Effect of Guide-ways Straightness on Measurement Accuracy ［J］. Machine Tool & Hydraulics, 2014, 42 (2): 97-99.
［3］戴国东. 水平仪测量导轨直线度误差数据的处理方法［J］. 科技风, 2017 (16), 167-168.
Dai G D. Measuring Geometric Error Based on Laser Collimator ［J］. Technology Wind, 2017 (16), 167-168.
［4］王孝坤. 利用激光跟踪仪测量超长导轨直线度的方法［J］. 应用光学, 2014, 34 (4): 686-689.
Wang X S. Testing Linearity Error of Long Guideway by Laser Tracker ［J］. Journal of Applied Optics,2014, 34(4): 686-689.
［5］胡长德, 陆加海, 幸褀, 等. 基于激光干涉的长导轨直线度误差测量［J］. 光学仪器, 2008, 30(6): 10-15.
Hu L D, Lu J H, Xing Q, et al. Long guide linearity error measurement based on laser interference ［J］. Optical Instruments, 2008, 30 (6): 10-15.
［6］房传明. 基于光学扫描法的长导轨直线度测量方法研究［D］. 苏州: 苏州大学,2014.
［7］常青, 尚智勇. 一种在线测量大尺寸直线度的方法［J］. 计量技术, 2018 (9): 19-22.
Chang Q, Shang Z Y. A method of on-line measurement of large-scale straightness a method of on-line measure-ment of large-scale straightness ［J］. Measurement Technique, 2018 (9): 19-22.
［8］羡一民, 刘洋. 干涉法测量直线度的原理分析［J］. 工具技术, 2015, 49 (5): 101-103.
Xian Y M, Liu Y. Principle Analysis of Interferometer for Straightness Measurement ［J］. Tool Engineering, 2015, 49 (5): 101-103.
［9］程亮. 激光外差干涉长行程精密导轨直线度测量及补偿方法研究［D］. 杭州: 浙江理工大学, 2017.
［10］Weichert C, Kchert P, Schtka E,et al. Investigation into the limitations of straightness interferometers using a mu-ltisensorbased error separation method ［J］. Measurement Science & Technology, 2018, 29(6): 064001.
［11］陈琪, 王晓飞, 石峰,等. 超长导轨直线度的测量和计算方法［J］. 上海计量测试, 2018, 45 (1): 40-41,45.
Chen Q, Wang X F, Shi F, et al. The Methods to Measure and Calculate the Straightness of Superlong Rail ［J］. Shanghai Measurement and Testing, 2018, 45 (1): 40-41,45.
［12］李婷, 李建双, ,缪东晶, 等. 温度条件对大尺寸测量装置精度影响的研究［J］. 计量学报, 2019, 40 (6): 975-979.
Li T, Li J S, Miao D J, et al. . Study of Temperature States Influence on the Accuracy of Large Size Measuring Devices ［J］. Acta Metrologica Sinica, 2019, 40 (6): 975-979.
［13］钱林弘, 吕磊, 夏欢. 基于拼接重构的长导轨直线度测量方法［J］. 组合机床与自动化加工技术,2017 (5): 77-80,84.
Qian L H, Lü L, Xia H. A Method for Measuring Straightness of Long Guideway Based on Stitching and Reconstruction ［J］. Modular Machine Tool & Automatic Manufacturing Technique, 2017 (5): 77-80,84.
［14］郭敬滨, 李斌. 大跨距、小步距法测量导轨系统的导轨直线度研究［J］. 机械科学与技术, 2013, 32 (11): 1600-1603.
Guo J B, Li B. On the Measurment of Guide Straigh-tness for the Guide System by Using the Large Span and Small Stride Method ［J］. Mechanical Science and Technology for Aerospace Engineering, 2013, 32 (11): 1600-1603.
［15］张凤翔, 赵辉. 直线度测量中采样间距与偏差形状关系的理论研究［J］. 航空计测技术, 1995, 15 (2): 9-11.
Zhang F X, Zhao H. Theory Research between Sample Step and Deviation Shape in Linearty Measrement ［J］. Aviation Metrology & Measurement Technology, 1995, 15 (2): 9-11.
［16］黄富贵. 直线度误差评定的测量提取点数选择［J］. 华侨大学学报 (自然科学版), 2011, 32 (6): 615-617.
Huang F G. Study on the Number of Extraction Points for Evaluation of Straightness Error ［J］. Journal of Huaqiao University (Natural Science), 2011, 32 (6): 615-617.
［17］Glubokov A V, Ped′ S E, Glubokova S V . Effect of the Number of Check Points of a Surface Profile on the Error of Measuring Deviations from Straightness ［J］. Measurement Techniques, 2017, 60 (2):134-139.
［18］贾立德, 郑子文, 李圣怡,等. 使用短基准的超精密长导轨直线度误差测量方法［J］. 机械工程学报, 2008, 44 (9): 141-147.
Jia L D,Zheng Z W, Li S Y, et al. Measurement Method of Straightness Error of a Long Ultra-precise Guideway with a Short Benchmark ［J］. Chinese Journal of Mechanical Engineering. 2008, 44 (9): 141-147.