|
|
Research on an Indirect Calibration Method of Micro/nano Coordinate Measuring Machine |
SHI Yu-shu1,2, GAO Si-tian2, SONG Xiao-ping2, GUO Xin3, CHEN Si-wen1, PI Lei2, LI Wei2, LI Qi2, LI Shi2, WANG Xing-wang2 |
1.State Key Laboratory of Precision Measurement Technology and Instruments, Tianjin University, Tianjin 300072, China
2.National Institute of Metrology, Beijing 100029, China
3.College of Metrology & Measurement Engineering, China Jiliang University, Hangzhou, Zhejiang 310018, China |
|
|
Abstract Since the high precision performance index of micro/nano coordinate measuring machine cannot be calibrated accurately, an indirect calibration solution is proposed. The measurement indication error of the micro/nano coordinate measuring machine is measured by gauge blocks and ball plate with hemispheres; The probing error is measured by calibration sphere. And a calibration experiment is done on the micro/nano coordinate measuring machining at National Institute of Metrology. The experimental results show that the error of indication of a CMM for size measurement is less than 0.2 μm, and the probing error is only 0.125 μm. The experiment results indicate that the error of indication of a CMM for size measurement and probing error are both less than their maximum permissible error, verifying the reasonability and feasibility of the calibration plan.
|
Received: 31 August 2015
Published: 28 December 2016
|
|
Corresponding Authors:
SHI Yu-shu
E-mail: shiys@nim.ac.cn
|
|
|
|
[1]张国雄. 三坐标测量机的发展趋势[J].中国机械工程, 2000, 11(1):222-226.
[2]荣列润. 三坐标测量机的现状和发展动向[J].机电一体化, 2001,(6):8-11.
[3]赵英剑,王建利,马新辉,等.三坐标测量机智能技术[J]. 计量学报, 2001, 22(3): 164-167.
[4]吴凤和,孙迎兵,王鑫. 基于HCGA的三坐标测量路径优化[J]. 计量学报, 2016,37(3):235-240.
[5]刘书桂, 张文杰. 用三坐标实现圆柱齿轮的自动测量与评价[J].计量学报, 1994,15(3):198-203.
[6]王华. 白车身制造尺寸质量控制中的软测量方法[J].计量学报, 2006, 27(4):309-310.
[7]程银宝,陈晓怀,王汉斌,等. CMM尺寸测量的不确定度评定模型研究[J].计量学报, 2016,37(5):462-466.
[8]位恒政, 王为农. 基于步距规的坐标测量机的误差补偿方法[J].仪器仪表学报, 2010,31(10):2374-2380.
[9]侯宇, 吕进. 三坐标测量机上形状误差评定的理论与方法[J].仪器仪表学报, 1996, 17(6):618-623.
[10]王晨晨. 异端类型坐标测量机结构原理及误差修正技术研究[D]. 合肥:合肥工业大学, 2012.
[11]JJF 1064-2010,坐标测量机校准规范[S].
[12]GB/T 16857.2—2006,产品几何技术规范(GPS) 坐标测量机的验收检测和复检检测 第2部分:用于测量尺寸的坐标测量机[S].
[13]王为农. 坐标测量机的溯源与校准规范[J].现代计量测试, 2000,(2):12-14.
[14]叶震宇. 坐标测量机校准中需要注意的问题[J].工业计量, 2012,(增刊1):120-121. |
|
|
|