转台负载工况下角位置误差补偿方法研究

doi:10.3969/j.issn.1000-1158.2024.06.07

Abstract
Figure/Table
References (14)
Related Citation (4)

Download: PDF (680 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Load affects the motion state of the rotary axis of the rotary table, which further affects the magnitude of the angular position error of the rotary table. By analysing the variation of the Fourier order of the rotary table angular position error under the load condition, an error compensation method based on harmonic compensation is proposed. Firstly, the influence of load on the rotary axis of the rotary table is analysed, the mathematical model between the rotary axis error motion and the angular position error is established, and numerical simulation is carried out. Secondly, the magnitude of the rotary axis error motion is affected by the load change, the self-calibration curves under different loads of the rotary table are obtained, and the Fourier order sensitive to the load change is analysed by the Fourier method. Finally, the Fourier order sensitive to load changes is selected to fit the harmonic compensation function to compensate the rotary table angular position error. The maximum angular position error of the rotary table under different load conditions after the error compensation is ±0.25″, which is ±0.03″ different from the angular position error under no-load conditions after the compensation, which effectively reduces the influence of load on the angular position error of the rotary table.

Key words： angular measurement rotary table variable load Fourier analysis error compensation

Received: 22 November 2023 Published: 06 June 2024

PACS:

TB922

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	XIAO Meiliang
	XUE Zi
	HUANG Yao
	ZHU Weibin
	LIN Hu
	YANG Yu

Cite this article:

XIAO Meiliang,XUE Zi,HUANG Yao, et al. Research on the Compensation Method of Angular Position Error under the Load Condition of Rotary Table[J]. Acta Metrologica Sinica, 2024, 45(6): 827-833.

URL:

http://jlxb.china-csm.org:81/Jwk_jlxb/EN/10.3969/j.issn.1000-1158.2024.06.07 OR http://jlxb.china-csm.org:81/Jwk_jlxb/EN/Y2024/V45/I6/827

［4］	许自镍. 圆光栅角度编码器测角误差补偿及新型结构研究［D］. 杭州: 杭州电子科技大学, 2021.
［10］	李尕丽, 薛梓, 黄垚,等. 全圆连续角度标准装置的系统误差分离与补偿［J］. 仪器仪表学报, 2021, 42(3): 1-9.
［13］	薛鹏飞. 回转轴转角误差与回转精度分析及测量［D］. 大连: 大连理工大学, 2019.
［5］	李凯, 袁峰. 基于蒙特卡洛法的圆光栅测角误差分析与补偿［J］. 光电子·激光, 2014, 25(7): 1381-1388.
［12］	刘力. 精密转台多自由度运动误差测量系统研究应用［D］. 大连: 大连理工大学, 2022.
［2］	JIAO Y, DING Y, DONG Z, et al. Optimal-arrangement-based four-scanning-heads error separation technique for self-calibration of angle encoders［J］. Measurement Science and Technology, 2018, 29(8): 085005.
	LI K, YUAN F. Measuring angles error analysis and compensation of circular grating sensor based on Monte Carlo method［J］. Journal of Optoelectronics·Laser, 2014, 25(7): 1381-1388.
［6］	高贯斌, 王文, 林铿,等. 基于RBF神经网络的关节转角误差补偿［J］. 机械工程学报, 2010, 46(12): 20-24.
	GAO G B, WANG W, LIN K, et al. Error Compensation of Joint Angles Based on RBF Neural Networks［J］. Journal of Mechanical Engineering, 2010, 46(12): 20-24.
［7］	CHEN G. Improving the angle measurement accuracy of circular grating［J］. Review of Scientific Instruments, 2020, 91(6):065108.
［8］	LI Y T, FAN K C. A novel method of angular positioning error analysis of rotary stages based on the Abbe principle［J］. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2018, 232(11): 1885-1892.
［11］	HOU J, XUE Z, HUANG Y, et al. Effect of varying load on angle measurement deviation of rotary table［C］//10th International Symposium on Precision Engineering Measurements and Instrumentation (ISPEMI 2018). Kunming, China, 2019.
［14］	乔丹, 薛梓, 黄垚,等. 等分多读数头位置偏差对测角误差的影响研究［J］. 计量学报, 2017, 38(6): 676-680.
	QIAO D, XUE Z, HUANG Y, et al. Study on influence of position deviation of multi-reading heads of equal average on angular measurement［J］. Acta Metrologica Sinica, 2017, 38(6) : 676-680.
［3］	WATANABE T, FUJIMOTO H, MASUDA T. Self-calibratable rotary encoder［C］//Journal of Physics: 7th International Symposium on Measurement Technology and Intelligent Instruments (ISMTII 2005). West Yorkshire, UK, 2005.
	LI G L, XUE Z, HUANG Y, et al. System error separation and compensation of the continuous full circle angle standard device［J］. Chinese Journal of Scientific Instrument, 2021, 42(3): 1-9.
［1］	HUANG Y, XUE Z, HUANG M, et al. The NIM continuous full circle angle standard［J］. Measurement Science & Technology, 2018, 29(7): 074013.
［9］	HOU B, ZHOU B, LI X, et al. Periodic nonlinear error analysis and compensation of a single-excited petal-shaped capacitive encoder to achieve high-accuracy measurement［J］. Sensors, 2019, 19(10): 2412.