[1]陈建超, 冯世绪, 郭保苏, 等. 表面微观形貌测量方法探讨[J]. 计量学报, 2016, 37(z1): 204-211.
Chen J C, Feng S X, Guo B S, et al. Methods employed for measuring surface microtopography[J]. Acta Metrologica Sinica, 2016, 37(z1): 204-211.
[2]蔡潇. 原子力显微镜在页岩微观孔隙结构研究中的应用[J]. 电子显微学报, 2015, 34(4): 326-331.
Cai X. Application of atomic force microscopy in thestudy of microscopic pore structure of shale[J]. Journal of Chinese Electron Microscopy Society, 2015, 34(4): 326-331.
[3]张龙飞, 王星睿, 邓晓, 等. 表面和亚表面特性对多层膜光栅成像对比度的影响[J]. 计量学报, 2018, 39(3): 13-17.
Zhang L F, Wang X R, Deng X, et al. Effect surface of sub-surface characteristics on the contrast of multilayer film grating imaging[J]. Acta Metrologica Sinica, 2018. 39(3): 13-17.
[4]韩国强, 景蔚萱, 蒋庄德, 等. 利用典型Si(100)微结构对原子力显微镜探针参数进行表征[J]. 计量学报, 2010, 31(5): 426-429.
Han G Q, Jing W X, Jiang Z D, et al. Characterization of AFM tip parameters with typical Si(100) microstructure[J]. Acta Metrologica Sinica, 2010, 31(5): 426-429.
[5]林启敬, 吴昊, 张福政, 等. Cu/Ti纳米薄膜表面形貌的分形表征研究[J]. 计量学报, 2018, 39(5): 593-597.
Lin Q J, Wu H, Zhang F Z, et al. Research on fractal characterization of the surface morphology of Cu/Ti nano thin film[J]. Acta Metrologica Sinica, 2018. 39(5): 593-597.
[6]王玄洋, 陈光. 超光滑光学元件表面疵病检测与控制[J]. 光学与光电技术, 2018, 16(04): 52-57.
Wang X G, Chen G. Super smooth optical component surface detection and control[J]. Optics & Optoelectronic Technology, 2018, 16(04): 52-57.
[7]耿延泉. 基于AFM的纳米加工深度模型及跨尺度结构加工工艺研究[D]. 哈尔滨: 哈尔滨工业大学, 2016.
[8]Zhong J, Sha Y L, Gan Y, et al. A Special Section on Instrumental Development and Application of Atomic Force Microscopy[J]. Science of Advanced Materials, 2017, 9(1): 52-54.
[9]Zhi F G, Zhao H G, Yong Wang W, et al. Application of Atomic Force Microscope and White Light Interfero-meter in Surface Material Tests[J]. Surface Technology, 2018, 47(1): 254-260.
[10]韩国强,陈玉琴. AFM线宽测量不确定度的分析与评定[J]. 计量学报, 2012, 33(6): 486-489.
Han G Q, Chen Y Q. Analysis and Evaluation of AFM Uncertainty in Linewidth Measurement[J]. Acta Metrologica Sinica, 2012, 33(6): 486-489.
[11]唐莹, 曹丛, 张健, 等. AFM设定值对测量准确度和探针寿命的影响[J]. 计量学报, 2019, 40(6A): 17-22.
Tang Y, Cao C, Zhang J, et al. The Effects of Different Setpoint to Measuring Accuracy and Service Life of a Probe on AFM[J]. Acta Metrologica Sinica, 2019, 40(6A): 17-22.
[12]Sulchek T, Yaralioglu G G, Quate C F, et al. Characterization and optimization of scan speed for tapping-mode atomic force microscopy[J]. Review of Scientific Instruments, 2002, 73(8): 2928-2936.
[13]Kodera N, Sakashita M, Ando T. Dynamic proportional-integral-differential controller for high-speed atomic force microscopy[J]. Review of Scientific Instruments, 2006, 77(8): 920-1192.
[14]Su C M, Huang L, Kjoller K. Direct measurement of tapping force with a cantilever deflection force sensor[J]. Ultramicroscopy, 2004, 100(3-4): 233-239.
[15]Xue B, Yan Y D, Hu Z J, et al. Study on effects of scan parameters on the image quality and tip wear in AFM tapping mode[J]. Scanning, 2014, 36(2): 263-269.
[16]Eves B J, Green R G. Limitations on accurate shape determination using amplitude modulation atomic force microscopy[J]. Ultramicroscopy, 2012, 115(115): 14-20.
[17]Thormann E, Pettersson T, Kettle J, et al. Probing material properties of polymeric surface layers with tapping mode AFM: which cantilever spring constant, tapping amplitude and amplitude set point gives good image contrast and minimal surface damage[J]. Ultramicroscopy, 2010, 110(4): 313-319. |