|
|
|
| Dynamic Calibration Method of Dual-wheel Friction Tester′s Measuring Model Based on Co-excitation Source |
| JING Gen-qiang1,2,GUO Hong-bo2,LIU Lu2,DUAN Fa-jie1,ZHANG Bing2 |
1. College of Precision Instrument & Opto-electronics Engineering, Tianjin University, Tianjin 300072, China
2. Research Institute of Highway, Ministry of Transport, Beijing 100088, China |
|
|
|
|
Abstract To characterize the measurement model of dual-wheel friction testers, the dynamic calibration method based on co-excitation source was proposed. In the method, counterforce constraint based dynamic calibration device was used for data collection, then data sequences matching was done, and mapping relation between the dataset of the objective sensor and that of the reference sensor was obtained. Finally, the parameters of measurement model were confirmed by grouping regression analysis and 2D optimization. The experimental results showed that the proposed method can achieve dynamic calibration of the dual-wheel friction tester′s measurement model with good adaptation to the variation of its state of motion. The residual sum of squares of fitting with the proposed method was reduced by over 50% comparing with the globle least square method.
|
|
Received: 10 February 2019
Published: 10 October 2019
|
|
|
|
|
|
［1］Hall J W, Smith K L, Titus-Glover L, et al. Guide for pavement friction. NCHRP. Web-only document 108. Contractor’s Final Report NCHRP Project 01-43［Z］. Transportation Research Board of the National Academes, 2009.
［2］Cerezo V, Gothié M. Adhera Research: A new approach for pavement performance evaluation［J］. Wear, 2009, 267(5-8): 1105-1110.
［3］Jafari K, Toufigh V. Interface between tire and pavement［J］. Journal of Materials in Civil Engineering, 2017, 29(9): 04017123.
［4］ASTM E303. Standard Test Method for Measuring Surface Frictional Properties Using the British Pendulum Tester［S］. 2013.
［5］ASTM E1911 2002. Standard test method for measuring paved surface frictional properties using the dynamic friction tester［S］. 2002
［6］ASTM E670 2009. Standard Test Method for Testing Side Force Friction on Paved Surfaces Using the Mu-Meter［S］. 2009.
［7］ASTM E274 2011. Standard Test Method for Skid Resistance of Paved Surfaces Using a Full-Scale Tire［S］. 2011.
［8］和松, 夏礼秀. 高速公路路面摩擦系数的测试与评价［J］. 公路交通科技, 2002, 19(1):8-11.
He S, Xia L X. Friction Coefficient Measurement and Evaluation for Lane Surface of Highway［J］. Journal of Highway and Transportation Research and Development, 2002, 19(1):8-11.
［9］沈训龙, 徐明波, 胡训仁. MU-Meter MK6路面摩擦系数测试系统应用研究［J］. 公路交通科技(应用技术版), 2009, 5(10):37-41.
Shen X L, Xu M B, Hu X R. Application Research for Mu-Meter MK6 Pavement Friction Coefficient Testing System［J］. Journal of Highway and Transportation Research and Development (Application Technology Edition), 2009, 5(10):37-41.
［10］中华人民共和国交通运输部. JTG E60－2008公路路基路面现场测试规程［S］. 2008.
［11］Vlajic N, Chijioke A. Traceable Dynamic Calibration of Force Transducers by Primary Means［J］. Metrologia, 2016, 53(4):S136-S148.
［12］胡红波, 孙桥, 白杰. 基于窄脉冲冲击激励的压电加速度计动态校准［J］. 计量学报, 2017, 38(2): 184-188.
Hu H B, Sun Q, Bai J. Dynamic Calibration of Accelerometer Using Short Shock Excitation［J］. Acta Metrologica Sinica, 2017, 38(2): 184-188.
［13］Prilepko M Y. Calibration and Validation of Dynamic Force Transducers［J］. Measurement Techniques, 2017, 60(1):1-5.
［14］何懿才, 廖建平, 赵君辙. 数学摆台法的超低频加速度校准［J］. 计量学报, 2017, 38(4):424-428.
He Y C, Liao J P, Zhao J Z. Calibration of Ultra-low Frequency Acceleration by Mathematical Pendulum-vibration Generator Method［J］. Acta Metrologica Sinica, 2017, 38(4):424-428. |
|
|
|
2019, Vol. 40 
