利用矢量网络分析仪单端口校准误差项提取二端口网络的S参数

孙静; 刘晨; 梁法国; 霍晔; 栾鹏; 吴爱华

doi:10.3969/j.issn.1000-1158.2021.11.14

PDF(2205 KB)

计量学报 ›› 2021, Vol. 42 ›› Issue (11) : 1499-1503. DOI: 10.3969/j.issn.1000-1158.2021.11.14

无线电、时间频率计量

利用矢量网络分析仪单端口校准误差项提取二端口网络的S参数

孙静,刘晨,梁法国,霍晔,栾鹏,吴爱华

作者信息 +

Extracting S-Parameter of Two-port Network by Using One-port Calibration Error Term of Vector Network Analyzer

SUN Jing,LIU Chen,LIANG Fa-guo,HUO Ye,LUAN Peng,WU Ai-hua

Author information +

文章历史 +

摘要

提出了一种利用矢量网络分析仪单端口校准误差项提取互易二端口网络S参数的方法。该方法要求在不同的参考平面上分别进行两次单端口校准,然后利用两次单端口校准的误差项求解二端口网络的S参数,通过实验验证该方法的正确性。该方法可应用于负载牵引和噪声参数测量过程中阻抗调配网络的S参数提取。

Abstract

A method to extract the S-parameters of the reciprocal two-port network by using the one-port calibration error term of the vector network analyzer is proposed. The method requires two one-port calibrations on difference planes, and then extract the S-parameter of two-port network by using vector network analyzer one-port calibration error term, the accuracy of the proposed method is verified by experiments. The method can be applied to S-parameter extraction of impedance deployment network during load pull and noise parameter measurement.

导出引用

孙静,刘晨,梁法国,霍晔,栾鹏,吴爱华. 利用矢量网络分析仪单端口校准误差项提取二端口网络的S参数[J]. 计量学报. 2021, 42(11): 1499-1503 https://doi.org/10.3969/j.issn.1000-1158.2021.11.14

SUN Jing,LIU Chen,LIANG Fa-guo,HUO Ye,LUAN Peng,WU Ai-hua. Extracting S-Parameter of Two-port Network by Using One-port Calibration Error Term of Vector Network Analyzer[J]. Acta Metrologica Sinica. 2021, 42(11): 1499-1503 https://doi.org/10.3969/j.issn.1000-1158.2021.11.14

中图分类号： TB973

参考文献

［1］郑易平. 负载牵引测量技术［J］. 电子测量技术, 2009, 32 (9):151-155.
Zheng Y P. Load pull measurement technique ［J］. Ele-ctronic Measurement Technology, 2009, 32 (9): 151-155.
［2］邢靖, 孙卫忠. 基于负载牵引测试系统的功率管参数提取［J］. 微波学报, 2009, 25 (3): 56-59.
Xing J, Sun W Z. Parameters Extraction of Power Tran-sistor Based on Load-Pull Measurement System ［J］. Journal of Microwaves, 2009, 25 (3): 56-59.
［3］Ferrero A, Teppati V, Carullo A. Accuracy evaluation of on-wafer load-pull measurements ［J］. IEEE Transactions on Microwave Theory & Techniques, 2001, 49 (1): 39-43.
［4］栾鹏, 王一帮, 梁法国, 等. 共面波导传输线电容准确测量及不确定度分析［J］. 计量学报, 2018, 39 (2): 272-275.
Luan P, Wang Y B, Liang F G, et al. Coplanar Wav-eguide Transmission Line Capacitance Measurement and Uncertainty Analysis ［J］. Acta Metrologica Sinica, 2018,39 (2): 272-275.
［5］Focus Microwave Inc. Basics on Load Pull and Noise Measurements［R］. Canada, Application Note 8, 1994.6.
［6］Gary S, David B, Joel D, et al. A New Noise Parameter Measurement Method Results in More than 100x Speed Improvement and Enhanced［C］//2008 72nd ARFTG Microwave Measurement Symposium. Portland, OR, 2008: 119-127.
［7］Ferreroand A, Pisani U.Two-port network analyzer cali-bration using an unknown ‘thru’ ［J］. IEEE Microwave and Guided Wave Letters, 1992, 2 (12): 505-507.
［8］Rytting D K. Network analyzer error models and calibra-tion methods［C］//Proc.ARFTG/NIST Short Course RF Meas.Wireless World. San Diego, CA, 2001: 29-30.
［9］Marks R B, Formulations of the Basic Vector Network Analyzer Error Model including Switch-Terms［C］//50th ARFTG Microwave Measurement Symposium. 1997: 115-126.
［10］Rumiantsev A,Ridler N.VNA calibration ［J］. IEEE Microwave Magazine, 2008, 9: 86-99.
［11］刘晨, 吴爱华, 孙静, 等. 宽带在片SOLT校准件研制及表征［J］. 计量学报, 2017, 38 (1): 98-101.
Liu C, Wu A H, Sun J, et al. Manufacturing and Characterizing of Broadband on-Wafer SOLT Calibration Standards ［J］. Acta Metrologica Sinica, 2017, 38 (1): 98-101.
［12］冯巍巍, 王幼林, 祝宁华.微波网络分析仪校准过程中校准方程的选择［J］. 计量学报, 2006, 27 (3): 269-272.
Feng W W, Wang Y L, Zhu N H. Choice of Calibration Equations in the Calibration of M icrowave Network Analyzer ［J］. Acta Metrologica Sinica, 2006, 27 (3): 269-272.
［13］Ou J, Caggiano M F. Determine Two-Port S-Parameters from One-Port Measurements using Calibration Substrate Standards［C］//Proceedings Electronic Components and Technology. Lake Buena Vista, FL.2005, 2: 1765-1768.
［14］Hietala V M. Determining Two-Port S-Parameters from a One-Port Measurement Using a Novel Impedance-State Test Chip ［C］//1999 IEEE MTT-S international Microwave Symposium Digest. Anaheim, CA, USA,1999, 4: 1639-1642.
［15］Hasar U C, Bute M. Error-Corrected Reflection and Transmission Scattering Parameters of a Two-Port Devi-ce ［J］. Microwave and Wireless Components Letters, 2017, 27 (7): 681-683.
［16］吴爱华, 刘晨, 王一帮, 等. 无源器件噪声标准值计算方法的研究［J］. 计量学报, 2018, 39 (1): 99-103.
Wu A H, Liu C, Wang Y B, et al. Research on Calculating Method about the Standard Value of Noise for Passive Device ［J］. Acta Metrologica Sinica, 2018, 39 (1): 99-103.
［17］孙伟, 田小建, 何炜瑜, 等. 共面微波探针在片测试技术研究［J］. 电子学报, 2001, 29 (2): 1-3.
Sun W, Tian X J, He W Y, et al. On-Wafer Measurement Technique Using Coplanar Microwave Pro-be ［J］. Acta Electronica Sinica, 2001, 29 (2): 1-3.
［18］吴爱华, 楼红英, 刘晨, 等. 提取共面微波探针S参数的方法［J］. 微波学报, 2016, 32 (2): 35-38.
Wu A H, Lou H Y, Liu C, et al. Methodology for Extracting S-Parameter of Coplanar Microwave Probe ［J］. Journal of Microwaves, 2016, 32 (2): 35-38.
［19］张立飞,杜静,王一帮, 等. 大反射负载牵引测量系统校准参数优化选取及应用［J］. 计量学报, 2021, 42 (7): 944-949.
Zhang L F, Du J, Wang Y B, et al. Selection and Application of Calibration Parameter Optimization for Traction Measurement System with Large Reflective Load［J］. Acta Metrologica Sinica, 2021, 42 (7): 944-949.
［20］王一帮,栾鹏,霍晔, 等. 基于矢量误差修正的实时负载牵引测量模型方法［J］. 计量学报, 2021, 42 (11):1494-1498.
Wang Y B, Luan P, Huo Y, et al. Real-time Load Pull Measurement Technique Based Vector Error Correction Method［J］. Acta Metrologica Sinica, 2021, 42 (11):1494-1498.