2025年04月10日 星期四 首页   |    期刊介绍   |    编 委 会   |    投稿指南   |    期刊订阅   |    统合信息   |    联系我们
计量学报  2024, Vol. 45 Issue (4): 480-488    DOI: 10.3969/j.issn.1000-1158.2024.04.03
  几何量计量 本期目录 | 过刊浏览 | 高级检索 |
基于LM方法的麻花钻刃带宽度测量研究
周正1,台立钢1,陈志远2,张禹1
1.沈阳工业大学机械工程学院,辽宁沈阳110870
2.沈阳市政集团沈阳市政集团有限公司,辽宁沈阳110026
Research on Measurement of Fried Dough Twists Drill Edge Band Width Based on LM Method
ZHOU Zheng1,TAI Ligang1,CHEN Zhiyuan2,ZHANG Yu1
1. School of Mechanical Engineering,Shenyang University of Technology,Shenyang, Liaoning 110870,China
2. Shenyang Municipal Group,Shenyang Municipal Group Corporation,Shenyang, Liaoning 110026,China
全文: PDF (15313 KB)   HTML (1 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 提出一种基于二值化的麻花钻刃带宽度检测方法。首先对目标边缘进行锐化,然后用巴特沃斯高通滤波提取边缘信息;其次通过改进的大津二值化算法对疑似边缘点进行阈值分割,获取边缘点坐标;再次使用列文伯格-马夸尔特(LM)方法对边缘附近的点进行拟合,得到刃带宽度曲线并求其拐点,求取麻花钻刃带宽度的数据。最后进行对比实验,用LM方法对未处理的M35直径2.5cm的刃带图像进行处理得到刃带宽度1.467mm,测量误差 0.467mm。改进后的测量结果为0.853mm,测量误差为0.147mm。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
周正
台立钢
陈志远
张禹
关键词 几何量计量麻花钻刃带宽度列文伯格-马夸尔特方法二值化算法视觉测量    
Abstract:A detection method of twist drill blade width based on binarization is proposed. Firstly, the target edge is sharpened, and then the edge information is extracted by Butterworth high-pass filtering. Secondly, through the improved Otsu binarization algorithm, the suspected edge points are threshold segmentation and the coordinates of the edge points are obtained. Again, the Levenberg-Marquardt(LM) method is used to fit the points near the edge, so as to get the edge band width curve and its inflection point, and get the data of edge band width of twist drill. Finally, the contrast experiment is carried out, and the untreated M35 blade image with a diameter of 2.5cm is processed by LM method, the blade width is 1.467mm, and the measurement error is 0.467mm.. The improved measurement result is 0.853mm and the measurement error is 0.147mm.
Key wordsgeometric measurement    width of twists drill blade    LM method    binary algorithm    visual measurement
收稿日期: 2023-07-11      发布日期: 2024-04-03
PACS:  TB92  
基金资助:国家自然科学基金(52005344,51775354);辽宁省科技厅重点实验室联合基金(2020-KF-12-07)
通讯作者: 张禹(1970-),辽宁沈阳人,沈阳工业大学教授,主要从事机器人导航、定位及其智能控制、水下机器人技术研究。Email:zhangyu@sut.edu.cn     E-mail: a13555786016@163.com
作者简介: 周正(1999-),辽宁沈阳人,沈阳工业大学研究生,研究方向为机器视觉与机器人。Email:1255736647@qq.com
引用本文:   
周正,台立钢,陈志远,张禹. 基于LM方法的麻花钻刃带宽度测量研究[J]. 计量学报, 2024, 45(4): 480-488.
ZHOU Zheng,TAI Ligang,CHEN Zhiyuan,ZHANG Yu. Research on Measurement of Fried Dough Twists Drill Edge Band Width Based on LM Method. Acta Metrologica Sinica, 2024, 45(4): 480-488.
链接本文:  
http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2024.04.03     或     http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2024/V45/I4/480
京ICP备:14006989号-1
版权所有 © 《计量学报》编辑部
地址:北三环东路18号(北京1413信箱)  邮编:100029 电话:(010)64271480
本系统由北京玛格泰克科技发展有限公司设计开发  技术支持:support@magtech.com.cn