2025年04月10日 星期四 首页   |    期刊介绍   |    编 委 会   |    投稿指南   |    期刊订阅   |    统合信息   |    联系我们
计量学报  2024, Vol. 45 Issue (4): 496-502    DOI: 10.3969/j.issn.1000-1158.2024.04.05
  几何量计量 本期目录 | 过刊浏览 | 高级检索 |
标准核燃料组件几何轮廓校准装置的研制
孙安斌1,2,高廷1,曹铁泽1,乔磊1
1.北京长城计量测试技术研究所,北京100095 2.北京航空航天大学,北京100191
Development of Geometric Profile Calibration Device for Standard Nuclear Fuel Assembly
SUN Anbin1,2,GAO Ting1,CAO Tieze1, QIAO Lei1
1. Beijing Changcheng Institute of Metrology and Measurement, Beijing 100095, China
2. Beijing University of Aeronautics and Astronautics, Beijing 100191, China
全文: PDF (7928 KB)   HTML (1 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 针对标准核燃料组件竖直状态下几何参数溯源需求,研制了一种标准核燃料组件几何轮廓校准装置。该装置以空间坐标测量为理念,利用多路接触式传感器作为轮廓测量采集单元,结合测量工作台高度位置获得轮廓坐标。通过直线度及扭转度测量与误差补偿,进一步提高了几何轮廓测量精度;并使用集成运动控制和专用测量软件,实现了标准核燃料组件几何轮廓参数(直线度、扭转度、垂直度、平行度)的自动检测。通过分析及实验验证,几何轮廓参数中直线度和平行度测量标准不确定度为0.01 mm,扭转度测量标准不确定度为0.007 mm,垂直度测量标准不确定度为0.017 mm,说明该装置能够满足标准核燃料组件的溯源需求。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
孙安斌
高廷
曹铁泽
乔磊
关键词 几何量计量核燃料组件几何轮廓校准直线度误差补偿    
Abstract:The standard nuclear fuel assembly is used for the on-site calibration of the nuclear fuel assembly measuring instrument. For the traceability requirements of geometric parameters of standard nuclear fuel assemblies, a geometric profile calibration device for standard nuclear fuel assembly is developed. Based on the concept of spatial coordinate measurement, the device uses multi-channel contact sensors as the profile measurement unit, and obtains the profile coordinates by combining the height position of the measuring table. Through straightness and torsion measurement and error compensation, the precision of geometric contour measurement is further improved. By integrating motion control and special measurement software, the standard nuclear fuel assembly geometric profile parameters (straightness, torsion, perpendicularity, parallelism) can be automatically detected. Through analysis and test, it is verified that the standard uncertainty of straightness and parallelism is 0.01 mm, the standard uncertainty of torsion is 0.007 mm and the standard uncertainty of perpendicularity is 0.017 mm. The above data show that the device can meet the traceability requirements of standard nuclear fuel assemblies.
Key wordsgeometric measurement    nuclear fuel assembly    geometric profile;calibration    straightness    err compensation
收稿日期: 2023-09-18      发布日期: 2024-04-03
PACS:  TB92  
基金资助:国家十三五技术基础科研项目(JSJL2016205B094)
作者简介: 孙安斌(1986- ),山东临沂人,北京长城计量测试技术研究所高级工程师,主要研究方向为大尺寸测量与校准技术。Email:sab276616@163.com
引用本文:   
孙安斌,高廷,曹铁泽,乔磊. 标准核燃料组件几何轮廓校准装置的研制[J]. 计量学报, 2024, 45(4): 496-502.
SUN Anbin,GAO Ting,CAO Tieze, QIAO Lei. Development of Geometric Profile Calibration Device for Standard Nuclear Fuel Assembly. Acta Metrologica Sinica, 2024, 45(4): 496-502.
链接本文:  
http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2024.04.05     或     http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2024/V45/I4/496
京ICP备:14006989号-1
版权所有 © 《计量学报》编辑部
地址:北三环东路18号(北京1413信箱)  邮编:100029 电话:(010)64271480
本系统由北京玛格泰克科技发展有限公司设计开发  技术支持:support@magtech.com.cn