2025年04月04日 星期五 首页   |    期刊介绍   |    编 委 会   |    投稿指南   |    期刊订阅   |    统合信息   |    联系我们
计量学报  2024, Vol. 45 Issue (2): 238-245    DOI: 10.3969/j.issn.1000-1158.2024.02.14
  力学计量 本期目录 | 过刊浏览 | 高级检索 |
基于弹性滚子接触模型的防滑纹对平板式动态汽车衡称重准确度影响分析
赖征创1,2,3,池辉2,3,杨晓翔1,4,张伟豪1
1.福州大学 机械工程及自动化学院,福建 福州 350116
2.福建省计量科学研究院(福建省力值计量测试重点实验室),福建 福州 350003
3.国家市场监管重点实验室(力值计量测试),福建 福州 350003
4.泉州师范学院,福建 泉州 362000)
Influence of Anti-skid Stripes on Weighing Accuracy of Flat DynamicWeighing Instrument Based on Elastic Roller Contact Model
LAI Zhengchuang1,2,3,CHI Hui2,3,YANG Xiaoxiang1,4,ZHANG Weihao1
1. College of Mechanical Engineering and Automation, Fuzhou University, Fuzhou, Fujian 350116, China
2. Fujian Metrology Institute, Fujian Key Laboratory of Force Measurement, Fuzhou, Fujian 350003, China
3. Key Laboratory of Force Measurement for State Market Regulation, Fuzhou, Fujian 350003, China
4. Quanzhou Normal University, Quanzhou, Fujian 362000, China
全文: PDF (730 KB)   HTML (1 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 动态称重时秤台防滑纹的垂向起伏会引起车辆发生振动,影响称重准确度。为此,建立了车辆称重过程的动力学模型,考虑轮胎的包容特性,建立弹性滚子接触模型,得出的防滑纹等效路面作为动力学模型的输入激励,分析各种因素作用下平板式汽车衡新型防滑纹对称重准确度的影响。仿真结果表明:随着防滑纹宽度增大,车辆的振动力变大,称重误差随之增大;凹坑型防滑纹间距为235mm时产生的激励频率接近于车辆的固有频率,引起车辆和秤台共振,称重误差最高可达0.21%。三角形状凹坑类型的防滑纹产生的振动力以及称重误差均低于矩形凹坑;车速越快,防滑纹的产生称重误差越大。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
赖征创
池辉
杨晓翔
张伟豪
关键词 力学计量汽车衡;车辆振动;动力学分析;防滑纹;弹性滚子接触模型;称重准确度    
Abstract:When dynamic weighing is carried out, the vertical undulation of the anti-skid pattern on the scale platform can cause vibrations in the vehicle, affecting weighing accuracy. To address this issue, a dynamic model of the vehicle weighing process was established, considering the compliance characteristics of the tires. An elastic roller contact model was developed, and the equivalent road surface generated by the anti-skid pattern was used as the input excitation for the dynamic model. The influence of a novel symmetrical anti-skid pattern on the accuracy of weighing in a flatbed scale under various factors was analyzed. Simulation results indicate that as the width of the anti-skid pattern increases, the vibration force on the vehicle increases, leading to an increase in weighing error. When the spacing between pit-type anti-skid patterns is 235mm, the excitation frequency generated approaches the natural frequency of the vehicle, causing resonance between the vehicle and the scale platform. The weighing error can reach a maximum of 0.21%. The vibration force and weighing error generated by triangular pit-type anti-skid patterns are lower than those of rectangular pits. Additionally, at higher speeds, the generation of anti-skid patterns results in larger weighing errors.
Key wordsmechanical metrology;dynamic weighing instrument    vehicle vibration    dynamic analysis    anti-skid stripes    elastic roller contact model    weighing accuracy
收稿日期: 2023-05-25      发布日期: 2024-02-21
PACS:  TB931  
基金资助:国家自然科学基金(11972005);福建省属公益类科研院所基本科研专项(2019R1016-2);泉州市科技局科技计划(2020C055)
通讯作者: 杨晓翔(1963-),男,内蒙古赤峰人,福州大学教授,博士生导师,主要从事计算力学方面研究。Email: yangxx@fzu.edu.cn     E-mail: lzcfjjl@126.com
作者简介: 赖征创(1986-),男,福建龙岩人,福州大学博士研究生,研究方向为测试计量技术及其工程应用。Email: lzcfjjl@126.com
引用本文:   
赖征创,池辉,杨晓翔,张伟豪. 基于弹性滚子接触模型的防滑纹对平板式动态汽车衡称重准确度影响分析[J]. 计量学报, 2024, 45(2): 238-245.
LAI Zhengchuang,CHI Hui,YANG Xiaoxiang,ZHANG Weihao. Influence of Anti-skid Stripes on Weighing Accuracy of Flat DynamicWeighing Instrument Based on Elastic Roller Contact Model. Acta Metrologica Sinica, 2024, 45(2): 238-245.
链接本文:  
http://jlxb.china-csm.org:81/Jwk_jlxb/CN/10.3969/j.issn.1000-1158.2024.02.14     或     http://jlxb.china-csm.org:81/Jwk_jlxb/CN/Y2024/V45/I2/238
京ICP备:14006989号-1
版权所有 © 《计量学报》编辑部
地址:北三环东路18号(北京1413信箱)  邮编:100029 电话:(010)64271480
本系统由北京玛格泰克科技发展有限公司设计开发  技术支持:support@magtech.com.cn