利用被测砝码和参考砝码在2种不同密度的空气介质中比较称量时,砝码间的质量差与空气密度差成线性变化这一特性,通过最小二乘法拟合质量差随空气密度差变化的曲线,提出了空气中双称量法砝码体积测量方法。基于空气中双称量法砝码体积测量数学模型和测量装置工作原理,分析影响测量结果的3个主要因素:2次测量的大气压变化范围,砝码表面解吸作用和质量比较仪计量特性。以10g~1kg OIML不锈钢砝码为例,将该方法测得的体积与液体静力比较法的测量结果比对,En值评定结果小于1。
Abstract
To study the linear change of mass difference and air density difference under two different air densities when comparing the test weight and reference weight, the least square method is used to fit the curve of mass difference and air density difference, and the double weighing in air volume determination method is proposed.Based on the mathematical model and the working principle of the measuring device, three main factors affecting the results are analyzed: the range of atmospheric pressure, the desorption of the weight surface and the mass comparator. Taking the 10g~1kg OIML stainless steel weight as an example, the volume determined by this method is compared with the result of the hydrostatic method, and the normalized error En is less than one.
关键词
计量学 /
体积测量 /
砝码 /
空气中双称量法 /
液体静力比较法
Key words
metrology /
volume determination /
weight /
double weighing in air method /
hydrostatic method
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
［1］International Organization of Legal Metrology. Weights of classes E1, E2, F1, F2, M1, M1-2, M2, M2-3 and M3 Part1: Metrological and technical requirements: OIML R 111-1 Weights ［S］. 2004.
［2］Ueki M, Sun J X, Ueda K. Performance Evaluation of a Mass Comparator with a readability of 0.1μg［C］// SICE Annual Conference, 2010.
［3］Clarkson M T, Davis R S, Sutton C M, et al. Determination of volumes of mass standards by weighings in air ［J］. Metrologia, 2001, 38 (1): 17-25.
［4］Ueki M, Mizushima S, Sun J X, et al. Simultaneous calibration of the mass and the volume of weights in the range from 1kg to 20kg ［C］//Proceedings of the 41st SICE Annual Conference. 2002.
［5］李德红, 黄建微, 沙比哈·吐尔逊, 等. g因子的蒙特卡罗模拟计算［J］. 计量学报, 2019, 40 (5): 920-923.
Li D H, Huang J W, Shabiha T, et al. Monte Carlo Simulation Method for g Factor［J］. Acta Metrologica Sinica, 2019, 40 (5): 920-923.
［6］陈超云, 张进明, 任学弟. 固体式密度天平校准系统的设计与实现［J］. 计量学报, 2018, 39 (6): 832-835.
Chen C Y, Zhang J M, Ren X D. Design and Implementation of Solid Density Balance Calibration System ［J］. Acta Metrologica Sinica, 2018, 39 (6): 832-835.
［7］张竟月, 王金涛, 时文才, 等. 液体密度量传中大气压强影响的研究［J］. 计量学报, 2018, 39 (2): 192-196.
Zhang J Y, Wang J T, Shi W C, et al. Study on the Influence of Ambient Pressure on Liquid Density Transmission ［J］. Acta Metrologica Sinica, 2018, 39 (2): 192-196.
［8］韩志, 王健, 罗哉. 质量基准量值传递过程中空气浮力影响的研究［J］. 计量学报, 2018, 39 (2): 151-154.
Han Z, Wang J, Luo Z. Study on the Influence of Air Buoyancy for the Dissemination Based on Mass Primary Standard ［J］. Acta Metrologica Sinica, 2018, 39 (2): 151-154.
［9］王晶, 黄爱军, 张婉洁. 砝码体积测量方法综述［J］. 制造业自动化, 2017, 39 (10): 65-69.
Wang J, Huang A J, Zhang W J. Review of weight volume measurement ［J］. Manufacturing Automation, 2017, 39 (10): 65-69.
［10］王肖磊, 王健, 钟瑞麟, 等. 砝码质量测量中的空气密度测量装置的研究［J］. 计量学报, 2011, 32 (1): 40-43.
Wang X L, Wang J, Zhong R L, et al. Study on Air Density Measurement for Measuring Weights ［J］. Acta Metrologica Sinica, 2011, 32 (1): 40-43.
［11］Malengo A, Bich W. Simultaneous determination of mass and volume of a standard by weighings in air ［J］. Metrologia, 2012, 49 (3): 289-299.
［12］Davis A P, Gleser M, Fujii K. Revised formula for the density of moist air (CIPM-2007) ［J］. Metrologia, 2008, 45 (2): 149-158.
［13］Kobata T, Ooiwa M A, Ishii A. Measurement of the volume of weights using an acoustic volumeter and the reliability of such measurement［J］. Metrologia, 2004, 41 (2): S75-S83.
［14］Tanaka M, Girard G, Davis R, Peuto A, et al. Recommended table for the density of water between 0℃ and 40℃ based on recent experimental reports［J］. Metrologia, 2001, 38 (4): 301-310.
［15］Cox M G. The evaluation of key comparison data［J］. Metrologia, 2002, 39 (6): 589-601.
基金
国家重点研发计划(2017YFF0205006)
PDF(929 KB)
